Disposable Vape Not Hitting After Charging – What Really Works

Every day, thousands of users charge their high-puff disposable vapes to 100%, see the green light, and still get nothing when they pull. This problem hits especially hard with 40,000 and 50,000-puff models because larger tanks, triple mesh coils, and child-lock systems create more points of failure. The good news: 95% of these cases fix in under one minute when you know the exact steps.

Buddacana has supplied factory-direct disposable vapes to wholesalers worldwide since 2019. Their catalog focuses on heavy-hitting, rechargeable devices built with real mesh coils, LED screens, and proper Type-C ports.Reach their team anytime through the contact page for instant support.

Why Is My Disposable Vape Still Not Hitting After Full Charge?

High-puff devices ship in locked mode to meet global child-safety rules. Cold oil thickens inside 36-40 ml tanks and blocks mesh coils. Low factory voltage settings also prevent firing until you wake the board.

Child Lock Still Engaged

Almost every 40K-50K unit leaves the factory locked. Five fast puffs within four seconds unlock it. The screen flashes or you hear a faint click.

Cold Oil + No Pre-Heat = Blocked Mesh Coils

Oil at room temperature or below refuses to wick properly through triple 0.6-ohm mesh. A 15-second pre-heat thins the oil and restores instant hits.

Low Voltage Mode or Factory Sleep Mode

Many boards default to 12-15 W to save battery during shipping. The coil never reaches vaporizing temperature until you raise power to 20-25 W.

How Do I Unlock Child Lock on High-Puff Disposables?

Press the fire button or puff five times fast. That is the universal standard across current production runs. The device confirms unlock with three flashes or a screen wake-up.

The Universal 5-Click Method

Five puffs or five clicks in under four seconds toggle the lock. Repeat the same sequence to lock it again when needed.

LED Confirmation Patterns You Should See

Three white flashes or the battery percentage appearing on screen means unlocked. No lights after five clicks usually means the board still sleeps.

What If 5 Clicks Do Nothing

Plug in the Type-C cable for ten minutes. The charging current forces the board awake, then repeat five clicks.

Does Pre-Heating Actually Fix a Dead-Hit Disposable?

Yes. Triple mesh coils in 40K and 50K devices need heat to pull thick oil. Skipping pre-heat is the second-biggest reason for no vapor.

Triple Mesh Coils Need 15-20 Seconds of Pre-Heat

Hold the button for two seconds or puff three times fast. The screen shows a flame icon while coils reach temperature.

Exact Button Combo for Large Shisha-Style Devices

Two-second press or three quick puffs starts pre-heat. The device vibrates or the flame icon counts down.

Visual Signs on the LED Screen That Pre-Heat Worked

The flame icon disappears and wattage numbers appear. Take a slow five-second pull; thick vapor confirms success.

Why Does My Disposable Show 100% Battery but Still Won’t Fire?

The battery can read full while voltage sags under load. Cheap 800 mAh cells drop too low for triple coils. Real 1100 mAh cells maintain steady power.

Voltage Drop Under Load

Smaller batteries collapse when triple mesh demands current. Premium cells in 50K models stay stable.

Micro-USB vs Real Type-C Charging Mistakes

Some cables only carry data, not full current. Always use the thick Type-C cable that came in the box.

Hidden “Power Save” Mode on 40K/50K Devices

Long press the fire button for five seconds to exit power-save. The screen brightness increases as proof.

Can Adjusting Airflow and Wattage Bring a Dead Vape Back to Life?

Open airflow and raise wattage solve 30% of remaining dead-hit cases.

Bottom Airflow Ring – Open It 100% First

Twist the base ring fully counterclockwise. Restricted airflow starves the coil of oxygen.

Screen Wattage Settings

Use the + button until the display reads 20-25 W. Lower settings produce no visible vapor.

Why Going Above 28W Kills Flavor and Coils Fast

Excess heat burns terpenes and shortens coil life. Stay under 28 W for best taste and longevity.

When Should I Just Contact Support Instead of Troubleshooting?

If five clicks, pre-heat, full airflow, and 25 W still produce nothing after a fresh charge, the unit likely has a rare factory fault.

Genuine Factory Fault vs User Error

No lights at all during charging points to a hardware issue. Any screen activity usually means user error.

Fastest Way to Reach Support

Visit Buddacana and send WhatsApp with your order number. Replies come within minutes during business hours.

Buddacana’s Spark Products

Two standout products in their lineup, the OKSO Shisha Max 40K and the OKSO Shisha Hookah Mega 50K, consistently earn praise for reliability once users master the simple activation sequence.

How to Completely Avoid the “Not Hitting After Charging” Problem Forever?

Follow a thirty-second first-use ritual and store devices properly.

Store Above 15°C / 59°F – Never in Car Glovebox

Cold thickens oil beyond recovery. Keep boxes at room temperature.

First-Use Ritual: Unlock → Pre-Heat → Charge 10 Min → Enjoy

Five clicks, pre-heat, short top-off charge, then vape. This sequence prevents 99% of complaints.

Why Choosing Proven 40K/50K Models Prevents 95% of Issues

Quality triple mesh, real 800-1100 mAh cells, and proper Type-C circuits eliminate most problems from the start.

FAQ

Q1: My screen shows 100% but no vapor after all steps. What now?
A: Message Buddacana on WhatsApp with your order number. They replace confirmed faulty units fast.

Q2: Is it normal for a new 50K device to need pre-heat every time?
A: Only the first 3-5 puffs after sitting idle. Once oil warms, hits stay instant.

Q3: Can I use any Type-C cable?
A: Use a cable rated for 2 A or higher. Thin phone cables often fail to deliver enough current.

Q4: How long should pre-heat last?
A: 15-20 seconds maximum. Longer than 30 seconds means airflow is still closed.

Q5: Will unlocking void warranty?
A: No. Five-click unlock is the intended activation method and never voids warranty.